Bud

Jul 15, 2023

SmartThings Edge Driver Instructions for Zooz 4-IN-1 SENSOR 700 (ZSE40 VER. 2.0)

Updated: Apr 7

This compact device detects and reports motion, temperature, humidity, and light level to your smart home app. The included CR123A battery makes the sensor lasts much longer than any previous version. Updated motion detection allows you to get even quicker activity reports. The Z-Wave chip provides better performance. Choose from 7 levels of motion sensitivity, adjust the motion clear delay time, and pick from 3 different LED indicator modes. This sensor is equipped with the latest S2 authenticated security and signal encryption. It's Z-Wave Plus 2 certified to ensure it complies with the highest industry standards. Supports SmartStart inclusion with a unique identifying PIN and QR code.

Here are the technical details for the Z-Wave Plus 4-in-1 Sensor ZSE40:

  • Z-Wave Signal Frequency: 908.42 MHz

  • Power: 1 CR123A battery (included in the box)

  • Z-Wave Range: Up to 100 feet line of sight

  • Installation and Use: Indoor Only

  • Operating Temperature: 5-104° F

  • Dimensions: 2.25" x 2.25" x 1"

Add your Smart ZSE40 to SmartThings in a few easy steps.

You will need to install the custom lua Edge driver for your sensor to be correctly recognized on SmartThings.

DEVICE ALREADY INCLUDED?:

  • Drivers can be manually assigned to a device! If you already have the device included (installed) to SmartThings, first follow the instructions in the section below to install the driver, then go to the device page by clicking on the device tile > click the 3 dots in top corner > select Driver > select Different Driver in blue at the bottom of driver page > select the Zooz Multisensor driver.

CUSTOM EDGE DRIVER INSTALLATION:

  1. Click on to the Zooz Channel invitation link here and log in with your Samsung / SmartThings account.

  2. Click Accept for Terms and Conditions.

  3. Select to Enroll your hub.

  4. If you're completing the process on a mobile device, you might see the screen load as if it were completing the request, but still show the Enroll button. Please try refreshing the screen, or going back a page, and then going to the enrollment page again - it should now show the Unenroll and Available Drivers options.

  5. Click the “Available Drivers” button.

  6. Scroll through the list and click the “Install” button for the Zooz Multisensor Driver.

  7. If you have multiple Zooz device models, you can install as many or all drivers if you'd like so that you don't have to repeat the process for other devices going forward. You won't need to install the driver for each device model if you have multiple of the same model. For example, if you have 3 x ZSE40 units, you only need to install the driver once and it will work for all 3.

  8. Wait a few minutes so that the updates are registered on your SmartThings hub.

  9. Join the device using the Scan QR Code method or the Scan for devices (manual inclusion) method or following the steps shown here.

  10. The device should be recognized as a Zooz Multisensor.

  11. Rename the device as needed and assign it to the room you want it in.

To change the settings in the app: once the driver is installed and the device is included to your SmartThings network, click on the ZSE40 in your app and tap the 3 dots in the top right corner of the app. Then tap Settings. There you'll be able to customize your device.

It's best to add your sensor from the target location to establish the best route from the hub on day one.

Here's how to add your ZSE40 to SmartThings:

  1. Tap the plus icon in the home screen

  2. Tap Add device

  3. Tap "Scan QR code"

  4. Scan the QR code on the label printed on the back of your sensor

  5. If prompted to activate the device, please press and release the Z-Wave button TWICE quickly with a paperclip

  6. The app will indicate when the device connects

  7. Tap Edit to rename the device, and tap Done to save the name

  8. Tap Done to complete the setup

Having issues including the sensor to SmartThings? You may need to reset it. The best way to approach this is through a Z-Wave exclusion from the SmartThings app (it works even if the sensor has never been added to SmartThings before):

  1. Tap on your hub in the home page of the app or on the device list

  2. Tap the three dots in the top right

  3. Tap Settings

  4. Tap Z-Wave Utilities

  5. Tap Z-Wave Exclusion

  6. While the app is searching for a device, press and release the Z-Wave button TWICE quickly with a paperclip

  7. The app will indicate when the device is successfully removed. Tap Done

Helped by this article? Consider a small donation. Donations of any sum sincerely appreciated. Thanks!

Find More Zooz and other SmartThings Compatible Smart Devices on my Amazon Store:

    4